Technician Class Question Pool 7/1/2022 to 6/30/2026 T1A01 (C) [97.1] Which of the following is part of the Basis and Purpose of the Amateur Radio Service? A. Providing personal radio communications for as many citizens as possible B. Providing communications for international non-profit organizations C. Advancing skills in the technical and communication phases of the radio art D. All these choices are correct T1A02 (C) [97.1] Which agency regulates and enforces the rules for the Amateur Radio Service in the United States? A. FEMA B. Homeland Security C. The FCC D. All these choices are correct T1A03 (B) [97.119(b)(2)] What do the FCC rules state regarding the use of a phonetic alphabet for station identification in the Amateur Radio Service? A. It is required when transmitting emergency messages B. It is encouraged C. It is required when in contact with foreign stations D. All these choices are correct T1A04 (A) [97.5(b)(1)] How many operator/primary station license grants may be held by any one person? A. One B. No more than two C. One for each band on which the person plans to operate D. One for each permanent station location from which the person plans to operate T1A05 (C) [97.7] What proves that the FCC has issued an operator/primary license grant? A. A printed copy of the certificate of successful completion of examination B. An email notification from the NCVEC granting the license C. The license appears in the FCC ULS database D. All these choices are correct T1A06 (D) [97.3(a)(9)] What is the FCC Part 97 definition of a beacon? A. A government transmitter marking the amateur radio band edges B. A bulletin sent by the FCC to announce a national emergency C. A continuous transmission of weather information authorized in the amateur bands by the National Weather Service D. An amateur station transmitting communications for the purposes of observing propagation or related experimental activities T1A07 (C) [97.3(a)(41)] What is the FCC Part 97 definition of a space station? A. Any satellite orbiting Earth B. A manned satellite orbiting Earth C. An amateur station located more than 50 km above Earth's surface D. An amateur station using amateur radio satellites for relay of signals T1A08 (B) [97.3(a)(22)] Which of the following entities recommends transmit/receive channels and other parameters for auxiliary and repeater stations? A. Frequency Spectrum Manager appointed by the FCC B. Volunteer Frequency Coordinator recognized by local amateurs C. FCC Regional Field Office D. International Telecommunication Union T1A09 (C) [97.3(a)(22)] Who selects a Frequency Coordinator? A. The FCC Office of Spectrum Management and Coordination Policy B. The local chapter of the Office of National Council of Independent Frequency Coordinators C. Amateur operators in a local or regional area whose stations are eligible to be repeater or auxiliary stations D. FCC Regional Field Office T1A10 (D) [97.3(a)(38), 97.407] What is the Radio Amateur Civil Emergency Service (RACES)? A. A radio service using amateur frequencies for emergency management or civil defense communications B. A radio service using amateur stations for emergency management or civil defense communications C. An emergency service using amateur operators certified by a civil defense organization as being enrolled in that organization D. All these choices are correct T1A11 (B) [97.101 (d)] When is willful interference to other amateur radio stations permitted? A. To stop another amateur station that is breaking the FCC rules B. At no time C. When making short test transmissions D. At any time, stations in the Amateur Radio Service are not protected from willful interference T1B01 (C) [97.301 (e)] Which of the following frequency ranges are available for phone operation by Technician licensees? A. 28.050 MHz to 28.150 MHz B. 28.100 MHz to 28.300 MHz C. 28.300 MHz to 28.500 MHz D. 28.500 MHz to 28.600 MHz T1B02 (B) [97.301, 97.207(c)] Which amateurs may contact the International Space Station (ISS) on VHF bands? A. Any amateur holding a General class or higher license B. Any amateur holding a Technician class or higher license C. Any amateur holding a General class or higher license who has applied for and received approval from NASA D. Any amateur holding a Technician class or higher license who has applied for and received approval from NASA T1B03 (B) [97.301(a)] Which frequency is in the 6 meter amateur band? A. 49.00 MHz B. 52.525 MHz C. 28.50 MHz D. 222.15 MHz T1B04 (D) [97.301(a)] Which amateur band includes 146.52 MHz? A. 6 meters B. 20 meters C. 70 centimeters D. 2 meters T1B05 (D) [97.305(c)] How may amateurs use the 219 to 220 MHz segment of 1.25 meter band? A. Spread spectrum only B. Fast-scan television only C. Emergency traffic only D. Fixed digital message forwarding systems only T1B06 (B) [97.301(e), 97.305] On which HF bands does a Technician class operator have phone privileges? A. None B. 10 meter band only C. 80 meter, 40 meter, 15 meter, and 10 meter bands D. 30 meter band only T1B07 (A) [97.305(a), (c)] Which of the following VHF/UHF band segments are limited to CW only? A. 50.0 MHz to 50.1 MHz and 144.0 MHz to 144.1 MHz B. 219 MHz to 220 MHz and 420.0 MHz to 420.1 MHz C. 902.0 MHz to 902.1 MHz D. All these choices are correct T1B08 (A) [97.303] How are US amateurs restricted in segments of bands where the Amateur Radio Service is secondary? A. U.S. amateurs may find non-amateur stations in those segments, and must avoid interfering with them B. U.S. amateurs must give foreign amateur stations priority in those segments C. International communications are not permitted in those segments D. Digital transmissions are not permitted in those segments T1B09 (D) [97.101(a), 97.301(a-e)] Why should you not set your transmit frequency to be exactly at the edge of an amateur band or sub-band? A. To allow for calibration error in the transmitter frequency display B. So that modulation sidebands do not extend beyond the band edge C. To allow for transmitter frequency drift D. All these choices are correct T1B10 (C) [97.305(c)] Where may SSB phone be used in amateur bands above 50 MHz? A. Only in sub-bands allocated to General class or higher licensees B. Only on repeaters C. In at least some segment of all these bands D. On any band if the power is limited to 25 watts T1B11 (A) [97.313] What is the maximum peak envelope power output for Technician class operators in their HF band segments? A. 200 watts B. 100 watts C. 50 watts D. 10 watts T1B12 (D) [97.313(b)] Except for some specific restrictions, what is the maximum peak envelope power output for Technician class operators using frequencies above 30 MHz? A. 50 watts B. 100 watts C. 500 watts D. 1500 watts T1C01 (D) [97.9(a), 97.17(a)] For which license classes are new licenses currently available from the FCC? A. Novice, Technician, General, Amateur Extra B. Technician, Technician Plus, General, Amateur Extra C. Novice, Technician Plus, General, Advanced D. Technician, General, Amateur Extra T1C02 (D) [97.19] Who may select a desired call sign under the vanity call sign rules? A. Only a licensed amateur with a General or Amateur Extra Class license B. Only a licensed amateur with an Amateur Extra Class license C. Only a licensed amateur who has been licensed continuously for more than 10 years D. Any licensed amateur T1C03 (A) [97.117] What types of international communications are an FCC-licensed amateur radio station permitted to make? A. Communications incidental to the purposes of the Amateur Radio Service and remarks of a personal character B. Communications incidental to conducting business or remarks of a personal nature C. Only communications incidental to contest exchanges; all other communications are prohibited D. Any communications that would be permitted by an international broadcast station T1C04 (B) [97.23] What may happen if the FCC is unable to reach you by email? A. Fine and suspension of operator license B. Revocation of the station license or suspension of the operator license C. Revocation of access to the license record in the FCC system D. Nothing; there is no such requirement T1C05 (A) Which of the following is a valid Technician class call sign format? A. KF1XXX B. KA1X C. W1XX D. All these choices are correct T1C06 (D) [97.5(a)(2)] From which of the following locations may an FCC-licensed amateur station transmit? A. From within any country that belongs to the International Telecommunication Union B. From within any country that is a member of the United Nations C. From anywhere within International Telecommunication Union (ITU) Regions 2 and 3 D. From any vessel or craft located in international waters and documented or registered in the United States T1C07 (B) [97.23] Which of the following can result in revocation of the station license or suspension of the operator license? A. Failure to inform the FCC of any changes in the amateur station following performance of an RF safety environmental evaluation B. Failure to provide and maintain a correct email address with the FCC C. Failure to obtain FCC type acceptance prior to using a home-built transmitter D. Failure to have a copy of your license available at your station T1C08 (C) [97.25] What is the normal term for an FCC-issued amateur radio license? A. Five years B. Life C. Ten years D. Eight years T1C09 (A) [97.21(a)(b)] What is the grace period for renewal if an amateur license expires? A. Two years B. Three years C. Five years D. Ten years T1C10 (C) [97.5a] How soon after passing the examination for your first amateur radio license may you transmit on the amateur radio bands? A. Immediately on receiving your Certificate of Successful Completion of Examination (CSCE) B. As soon as your operator/station license grant appears on the ARRL website C. As soon as your operator/station license grant appears in the FCC’s license database D. As soon as you receive your license in the mail from the FCC T1C11 (D) [97.21(b)] If your license has expired and is still within the allowable grace period, may you continue to transmit on the amateur radio bands? A. Yes, for up to two years B. Yes, as soon as you apply for renewal C. Yes, for up to one year D. No, you must wait until the license has been renewed T1D01 (A) [97.111(a)(1)] With which countries are FCC-licensed amateur radio stations prohibited from exchanging communications? A. Any country whose administration has notified the International Telecommunication Union (ITU) that it objects to such communications B. Any country whose administration has notified the American Radio Relay League (ARRL) that it objects to such communications C. Any country banned from such communications by the International Amateur Radio Union (IARU) D. Any country banned from making such communications by the American Radio Relay League (ARRL) T1D02 (B) [97.113(b), 97.111(b)] Under which of the following circumstances are one-way transmissions by an amateur station prohibited? A. In all circumstances B. Broadcasting C. International Morse Code Practice D. Telecommand or transmissions of telemetry T1D03 (C) [97.211(b), 97.215(b), 97.113(a)(4)] When is it permissible to transmit messages encoded to obscure their meaning? A. Only during contests B. Only when transmitting certain approved digital codes C. Only when transmitting control commands to space stations or radio control craft D. Never T1D04 (A) [97.113(a)(4), 97.113(c)] Under what conditions is an amateur station authorized to transmit music using a phone emission? A. When incidental to an authorized retransmission of manned spacecraft communications B. When the music produces no spurious emissions C. When transmissions are limited to less than three minutes per hour D. When the music is transmitted above 1280 MHz T1D05 (D) [97.113(a)(3)(ii)] When may amateur radio operators use their stations to notify other amateurs of the availability of equipment for sale or trade? A. Never B. When the equipment is not the personal property of either the station licensee, or the control operator, or their close relatives C. When no profit is made on the sale D. When selling amateur radio equipment and not on a regular basis T1D06 (B) [97.113(a)(4)] What, if any, are the restrictions concerning transmission of language that may be considered indecent or obscene? A. The FCC maintains a list of words that are not permitted to be used on amateur frequencies B. Any such language is prohibited C. The ITU maintains a list of words that are not permitted to be used on amateur frequencies D. There is no such prohibition T1D07 (D) [97.113(d)] What types of amateur stations can automatically retransmit the signals of other amateur stations? A. Auxiliary, beacon, or Earth stations B. Earth, repeater, or space stations C. Beacon, repeater, or space stations D. Repeater, auxiliary, or space stations T1D08 (B) [97.113(a)(3)(iii)] In which of the following circumstances may the control operator of an amateur station receive compensation for operating that station? A. When the communication is related to the sale of amateur equipment by the control operator's employer B. When the communication is incidental to classroom instruction at an educational institution C. When the communication is made to obtain emergency information for a local broadcast station D. All these choices are correct T1D09 (A) [97.113(5)(b)] When may amateur stations transmit information in support of broadcasting, program production, or news gathering, assuming no other means is available? A. When such communications are directly related to the immediate safety of human life or protection of property B. When broadcasting communications to or from the space shuttle C. Where noncommercial programming is gathered and supplied exclusively to the National Public Radio network D. Never T1D10 (D) [97.3(a)(10)] How does the FCC define broadcasting for the Amateur Radio Service? A. Two-way transmissions by amateur stations B. Any transmission made by the licensed station C. Transmission of messages directed only to amateur operators D. Transmissions intended for reception by the general public T1D11 (D) [97.119(a)] When may an amateur station transmit without identifying on the air? A. When the transmissions are of a brief nature to make station adjustments B. When the transmissions are unmodulated C. When the transmitted power level is below 1 watt D. When transmitting signals to control model craft T1E01 (D) [97.7(a)] When may an amateur station transmit without a control operator? A. When using automatic control, such as in the case of a repeater B. When the station licensee is away and another licensed amateur is using the station C. When the transmitting station is an auxiliary station D. Never T1E02 (D) [97.301, 97.207(c)] Who may be the control operator of a station communicating through an amateur satellite or space station? A. Only an Amateur Extra Class operator B. A General class or higher licensee with a satellite operator certification C. Only an Amateur Extra Class operator who is also an AMSAT member D. Any amateur allowed to transmit on the satellite uplink frequency T1E03 (A) [97.103(b)] Who must designate the station control operator? A. The station licensee B. The FCC C. The frequency coordinator D. Any licensed operator T1E04 (D) [97.103(b)] What determines the transmitting frequency privileges of an amateur station? A. The frequency authorized by the frequency coordinator B. The frequencies printed on the license grant C. The highest class of operator license held by anyone on the premises D. The class of operator license held by the control operator T1E05 (C) [97.3(a)(14)] What is an amateur station’s control point? A. The location of the station’s transmitting antenna B. The location of the station’s transmitting apparatus C. The location at which the control operator function is performed D. The mailing address of the station licensee T1E06 (A) [97.301] When, under normal circumstances, may a Technician class licensee be the control operator of a station operating in an Amateur Extra Class band segment? A. At no time B. When designated as the control operator by an Amateur Extra Class licensee C. As part of a multi-operator contest team D. When using a club station whose trustee holds an Amateur Extra Class license T1E07 (D) [97.103(a)] When the control operator is not the station licensee, who is responsible for the proper operation of the station? A. All licensed amateurs who are present at the operation B. Only the station licensee C. Only the control operator D. The control operator and the station licensee T1E08 (A) [97.3(a)(6), 97.205(d)] Which of the following is an example of automatic control? A. Repeater operation B. Controlling a station over the internet C. Using a computer or other device to send CW automatically D. Using a computer or other device to identify automatically T1E09 (D) [97.109(c)] Which of the following are required for remote control operation? A. The control operator must be at the control point B. A control operator is required at all times C. The control operator must indirectly manipulate the controls D. All these choices are correct T1E10 (B) [97.3(a)(39)] Which of the following is an example of remote control as defined in Part 97? A. Repeater operation B. Operating the station over the internet C. Controlling a model aircraft, boat, or car by amateur radio D. All these choices are correct T1E11 (D) [97.103(a)] Who does the FCC presume to be the control operator of an amateur station, unless documentation to the contrary is in the station records? A. The station custodian B. The third party participant C. The person operating the station equipment D. The station licensee T1F01 (B) [97.103(c)] When must the station and its records be available for FCC inspection? A. At any time ten days after notification by the FCC of such an inspection B. At any time upon request by an FCC representative C. At any time after written notification by the FCC of such inspection D. Only when presented with a valid warrant by an FCC official or government agent T1F02 (C) [97.119 (a)] How often must you identify with your FCC-assigned call sign when using tactical call signs such as “Race Headquarters”? A. Never, the tactical call is sufficient B. Once during every hour C. At the end of each communication and every ten minutes during a communication D. At the end of every transmission T1F03 (D) [97.119(a)] When are you required to transmit your assigned call sign? A. At the beginning of each contact, and every 10 minutes thereafter B. At least once during each transmission C. At least every 15 minutes during and at the end of a communication D. At least every 10 minutes during and at the end of a communication T1F04 (C) [97.119(b)(2)] What language may you use for identification when operating in a phone sub-band? A. Any language recognized by the United Nations B. Any language recognized by the ITU C. English D. English, French, or Spanish T1F05 (B) [97.119(b)(2)] What method of call sign identification is required for a station transmitting phone signals? A. Send the call sign followed by the indicator RPT B. Send the call sign using a CW or phone emission C. Send the call sign followed by the indicator R D. Send the call sign using only a phone emission T1F06 (D) [97.119(c)] Which of the following self-assigned indicators are acceptable when using a phone transmission? A. KL7CC stroke W3 B. KL7CC slant W3 C. KL7CC slash W3 D. All these choices are correct T1F07 (B) [97.115(a)(2)] Which of the following restrictions apply when a non-licensed person is allowed to speak to a foreign station using a station under the control of a licensed amateur operator? A. The person must be a U.S. citizen B. The foreign station must be in a country with which the U.S. has a third party agreement C. The licensed control operator must do the station identification D. All these choices are correct T1F08 (A) [97.3(a)(47)] What is the definition of third party communications? A. A message from a control operator to another amateur station control operator on behalf of another person B. Amateur radio communications where three stations are in communications with one another C. Operation when the transmitting equipment is licensed to a person other than the control operator D. Temporary authorization for an unlicensed person to transmit on the amateur bands for technical experiments T1F09 (C) [97.3(a)(40)] What type of amateur station simultaneously retransmits the signal of another amateur station on a different channel or channels? A. Beacon station B. Earth station C. Repeater station D. Message forwarding station T1F10 (A) [97.205(g)] Who is accountable if a repeater inadvertently retransmits communications that violate the FCC rules? A. The control operator of the originating station B. The control operator of the repeater C. The owner of the repeater D. Both the originating station and the repeater owner T1F11 (B) [97.5(b)(2)] Which of the following is a requirement for the issuance of a club station license grant? A. The trustee must have an Amateur Extra Class operator license grant B. The club must have at least four members C. The club must be registered with the American Radio Relay League D. All these choices are correct T2A01 (B) What is a common repeater frequency offset in the 2 meter band? A. Plus or minus 5 MHz B. Plus or minus 600 kHz C. Plus or minus 500 kHz D. Plus or minus 1 MHz T2A02 (A) What is the national calling frequency for FM simplex operations in the 2 meter band? A. 146.520 MHz B. 145.000 MHz C. 432.100 MHz D. 446.000 MHz T2A03 (A) What is a common repeater frequency offset in the 70 cm band? A. Plus or minus 5 MHz B. Plus or minus 600 kHz C. Plus or minus 500 kHz D. Plus or minus 1 MHz T2A04 (B) What is an appropriate way to call another station on a repeater if you know the other station's call sign? A. Say "break, break," then say the station's call sign B. Say the station's call sign, then identify with your call sign C. Say "CQ" three times, then the other station's call sign D. Wait for the station to call CQ, then answer T2A05 (C) How should you respond to a station calling CQ? A. Transmit "CQ" followed by the other station’s call sign B. Transmit your call sign followed by the other station’s call sign C. Transmit the other station’s call sign followed by your call sign D. Transmit a signal report followed by your call sign T2A06 (A) Which of the following is required when making on-the-air test transmissions? A. Identify the transmitting station B. Conduct tests only between 10 p.m. and 6 a.m. local time C. Notify the FCC of the transmissions D. All these choices are correct T2A07 (A) What is meant by "repeater offset”? A. The difference between a repeater’s transmit and receive frequencies B. The repeater has a time delay to prevent interference C. The repeater station identification is done on a separate frequency D. The number of simultaneous transmit frequencies used by a repeater T2A08 (D) What is the meaning of the procedural signal “CQ”? A. Call on the quarter hour B. Test transmission, no reply expected C. Only the called station should transmit D. Calling any station T2A09 (B) Which of the following indicates that a station is listening on a repeater and looking for a contact? A. “CQ CQ” followed by the repeater’s call sign B. The station’s call sign followed by the word “monitoring” C. The repeater call sign followed by the station’s call sign D. “QSY” followed by your call sign T2A10 (A) What is a band plan, beyond the privileges established by the FCC? A. A voluntary guideline for using different modes or activities within an amateur band B. A list of operating schedules C. A list of available net frequencies D. A plan devised by a club to indicate frequency band usage T2A11 (C) What term describes an amateur station that is transmitting and receiving on the same frequency? A. Full duplex B. Diplex C. Simplex D. Multiplex T2A12 (D) What should you do before calling CQ? A. Listen first to be sure that no one else is using the frequency B. Ask if the frequency is in use C. Make sure you are authorized to use that frequency D. All these choices are correct T2B01 (C) How is a VHF/UHF transceiver’s “reverse” function used? A. To reduce power output B. To increase power output C. To listen on a repeater’s input frequency D. To listen on a repeater’s output frequency T2B02 (D) What term describes the use of a sub-audible tone transmitted along with normal voice audio to open the squelch of a receiver? A. Carrier squelch B. Tone burst C. DTMF D. CTCSS T2B03 (A) Which of the following describes a linked repeater network? A. A network of repeaters in which signals received by one repeater are transmitted by all the repeaters in the network B. A single repeater with more than one receiver C. Multiple repeaters with the same control operator D. A system of repeaters linked by APRS T2B04 (D) Which of the following could be the reason you are unable to access a repeater whose output you can hear? A. Improper transceiver offset B. You are using the wrong CTCSS tone C. You are using the wrong DCS code D. All these choices are correct T2B05 (C) What would cause your FM transmission audio to be distorted on voice peaks? A. Your repeater offset is inverted B. You need to talk louder C. You are talking too loudly D. Your transmit power is too high T2B06 (A) What type of signaling uses pairs of audio tones? A. DTMF B. CTCSS C. GPRS D. D-STAR T2B07 (C) How can you join a digital repeater’s “talkgroup”? A. Register your radio with the local FCC office B. Join the repeater owner’s club C. Program your radio with the group’s ID or code D. Sign your call after the courtesy tone T2B08 (A) Which of the following applies when two stations transmitting on the same frequency interfere with each other? A. The stations should negotiate continued use of the frequency B. Both stations should choose another frequency to avoid conflict C. Interference is inevitable, so no action is required D. Use subaudible tones so both stations can share the frequency T2B09 (A) Why are simplex channels designated in the VHF/UHF band plans? A. So stations within range of each other can communicate without tying up a repeater B. For contest operation C. For working DX only D. So stations with simple transmitters can access the repeater without automated offset T2B10 (A) Which Q signal indicates that you are receiving interference from other stations? A. QRM B. QRN C. QTH D. QSB T2B11 (B) Which Q signal indicates that you are changing frequency? A. QRU B. QSY C. QSL D. QRZ T2B12 (A) What is the purpose of the color code used on DMR repeater systems? A. Must match the repeater color code for access B. Defines the frequency pair to use C. Identifies the codec used D. Defines the minimum signal level required for access T2B13 (B) What is the purpose of a squelch function? A. Reduce a CW transmitter's key clicks B. Mute the receiver audio when a signal is not present C. Eliminate parasitic oscillations in an RF amplifier D. Reduce interference from impulse noise T2C01 (D) [97.103(a)] When do FCC rules NOT apply to the operation of an amateur station? A. When operating a RACES station B. When operating under special FEMA rules C. When operating under special ARES rules D. FCC rules always apply T2C02 (C) Which of the following are typical duties of a Net Control Station? A. Choose the regular net meeting time and frequency B. Ensure that all stations checking into the net are properly licensed for operation on the net frequency C. Call the net to order and direct communications between stations checking in D. All these choices are correct T2C03 (C) What technique is used to ensure that voice messages containing unusual words are received correctly? A. Send the words by voice and Morse code B. Speak very loudly into the microphone C. Spell the words using a standard phonetic alphabet D. All these choices are correct T2C04 (D) What is RACES? A. An emergency organization combining amateur radio and citizens band operators and frequencies B. An international radio experimentation society C. A radio contest held in a short period, sometimes called a “sprint” D. An FCC part 97 amateur radio service for civil defense communications during national emergencies T2C05 (A) What does the term “traffic” refer to in net operation? A. Messages exchanged by net stations B. The number of stations checking in and out of a net C. Operation by mobile or portable stations D. Requests to activate the net by a served agency T2C06 (A) What is the Amateur Radio Emergency Service (ARES)? A. A group of licensed amateurs who have voluntarily registered their qualifications and equipment for communications duty in the public service B. A group of licensed amateurs who are members of the military and who voluntarily agreed to provide message handling services in the case of an emergency C. A training program that provides licensing courses for those interested in obtaining an amateur license to use during emergencies D. A training program that certifies amateur operators for membership in the Radio Amateur Civil Emergency Service T2C07 (C) Which of the following is standard practice when you participate in a net? A. When first responding to the net control station, transmit your call sign, name, and address as in the FCC database B. Record the time of each of your transmissions C. Unless you are reporting an emergency, transmit only when directed by the net control station D. All these choices are correct T2C08 (A) Which of the following is a characteristic of good traffic handling? A. Passing messages exactly as received B. Making decisions as to whether messages are worthy of relay or delivery C. Ensuring that any newsworthy messages are relayed to the news media D. All these choices are correct T2C09 (D) Are amateur station control operators ever permitted to operate outside the frequency privileges of their license class? A. No B. Yes, but only when part of a FEMA emergency plan C. Yes, but only when part of a RACES emergency plan D. Yes, but only in situations involving the immediate safety of human life or protection of property T2C10 (D) What information is contained in the preamble of a formal traffic message? A. The email address of the originating station B. The address of the intended recipient C. The telephone number of the addressee D. Information needed to track the message T2C11 (A) What is meant by “check” in a radiogram header? A. The number of words or word equivalents in the text portion of the message B. The call sign of the originating station C. A list of stations that have relayed the message D. A box on the message form that indicates that the message was received and/or relayed T3A01 (C) Why do VHF signal strengths sometimes vary greatly when the antenna is moved only a few feet? A. The signal path encounters different concentrations of water vapor B. VHF ionospheric propagation is very sensitive to path length C. Multipath propagation cancels or reinforces signals D. All these choices are correct T3A02 (B) What is the effect of vegetation on UHF and microwave signals? A. Knife-edge diffraction B. Absorption C. Amplification D. Polarization rotation T3A03 (C) What antenna polarization is normally used for long-distance CW and SSB contacts on the VHF and UHF bands? A. Right-hand circular B. Left-hand circular C. Horizontal D. Vertical T3A04 (B) What happens when antennas at opposite ends of a VHF or UHF line of sight radio link are not using the same polarization? A. The modulation sidebands might become inverted B. Received signal strength is reduced C. Signals have an echo effect D. Nothing significant will happen T3A05 (B) When using a directional antenna, how might your station be able to communicate with a distant repeater if buildings or obstructions are blocking the direct line of sight path? A. Change from vertical to horizontal polarization B. Try to find a path that reflects signals to the repeater C. Try the long path D. Increase the antenna SWR T3A06 (B) What is the meaning of the term “picket fencing”? A. Alternating transmissions during a net operation B. Rapid flutter on mobile signals due to multipath propagation C. A type of ground system used with vertical antennas D. Local vs long-distance communications T3A07 (C) What weather condition might decrease range at microwave frequencies? A. High winds B. Low barometric pressure C. Precipitation D. Colder temperatures T3A08 (D) What is a likely cause of irregular fading of signals propagated by the ionosphere? A. Frequency shift due to Faraday rotation B. Interference from thunderstorms C. Intermodulation distortion D. Random combining of signals arriving via different paths T3A09 (B) Which of the following results from the fact that signals propagated by the ionosphere are elliptically polarized? A. Digital modes are unusable B. Either vertically or horizontally polarized antennas may be used for transmission or reception C. FM voice is unusable D. Both the transmitting and receiving antennas must be of the same polarization T3A10 (D) What effect does multi-path propagation have on data transmissions? A. Transmission rates must be increased by a factor equal to the number of separate paths observed B. Transmission rates must be decreased by a factor equal to the number of separate paths observed C. No significant changes will occur if the signals are transmitted using FM D. Error rates are likely to increase T3A11 (C) Which region of the atmosphere can refract or bend HF and VHF radio waves? A. The stratosphere B. The troposphere C. The ionosphere D. The mesosphere T3A12 (B) What is the effect of fog and rain on signals in the 10 meter and 6 meter bands? A. Absorption B. There is little effect C. Deflection D. Range increase T3B01 (D) What is the relationship between the electric and magnetic fields of an electromagnetic wave? A. They travel at different speeds B. They are in parallel C. They revolve in opposite directions D. They are at right angles T3B02 (A) What property of a radio wave defines its polarization? A. The orientation of the electric field B. The orientation of the magnetic field C. The ratio of the energy in the magnetic field to the energy in the electric field D. The ratio of the velocity to the wavelength T3B03 (C) What are the two components of a radio wave? A. Impedance and reactance B. Voltage and current C. Electric and magnetic fields D. Ionizing and non-ionizing radiation T3B04 (A) What is the velocity of a radio wave traveling through free space? A. Speed of light B. Speed of sound C. Speed inversely proportional to its wavelength D. Speed that increases as the frequency increases T3B05 (B) What is the relationship between wavelength and frequency? A. Wavelength gets longer as frequency increases B. Wavelength gets shorter as frequency increases C. Wavelength and frequency are unrelated D. Wavelength and frequency increase as path length increases T3B06 (D) What is the formula for converting frequency to approximate wavelength in meters? A. Wavelength in meters equals frequency in hertz multiplied by 300 B. Wavelength in meters equals frequency in hertz divided by 300 C. Wavelength in meters equals frequency in megahertz divided by 300 D. Wavelength in meters equals 300 divided by frequency in megahertz T3B07 (A) In addition to frequency, which of the following is used to identify amateur radio bands? A. The approximate wavelength in meters B. Traditional letter/number designators C. Channel numbers D. All these choices are correct T3B08 (B) What frequency range is referred to as VHF? A. 30 kHz to 300 kHz B. 30 MHz to 300 MHz C. 300 kHz to 3000 kHz D. 300 MHz to 3000 MHz T3B09 (D) What frequency range is referred to as UHF? A. 30 to 300 kHz B. 30 to 300 MHz C. 300 to 3000 kHz D. 300 to 3000 MHz T3B10 (C) What frequency range is referred to as HF? A. 300 to 3000 MHz B. 30 to 300 MHz C. 3 to 30 MHz D. 300 to 3000 kHz T3B11 (B) What is the approximate velocity of a radio wave in free space? A. 150,000 meters per second B. 300,000,000 meters per second C. 300,000,000 miles per hour D. 150,000 miles per hour T3C01 (C) Why are simplex UHF signals rarely heard beyond their radio horizon? A. They are too weak to go very far B. FCC regulations prohibit them from going more than 50 miles C. UHF signals are usually not propagated by the ionosphere D. UHF signals are absorbed by the ionospheric D region T3C02 (C) What is a characteristic of HF communication compared with communications on VHF and higher frequencies? A. HF antennas are generally smaller B. HF accommodates wider bandwidth signals C. Long-distance ionospheric propagation is far more common on HF D. There is less atmospheric interference (static) on HF T3C03 (B) What is a characteristic of VHF signals received via auroral backscatter? A. They are often received from 10,000 miles or more B. They are distorted and signal strength varies considerably C. They occur only during winter nighttime hours D. They are generally strongest when your antenna is aimed west T3C04 (B) Which of the following types of propagation is most commonly associated with occasional strong signals on the 10, 6, and 2 meter bands from beyond the radio horizon? A. Backscatter B. Sporadic E C. D region absorption D. Gray-line propagation T3C05 (A) Which of the following effects may allow radio signals to travel beyond obstructions between the transmitting and receiving stations? A. Knife-edge diffraction B. Faraday rotation C. Quantum tunneling D. Doppler shift T3C06 (A) What type of propagation is responsible for allowing over-the-horizon VHF and UHF communications to ranges of approximately 300 miles on a regular basis? A. Tropospheric ducting B. D region refraction C. F2 region refraction D. Faraday rotation T3C07 (B) What band is best suited for communicating via meteor scatter? A. 33 centimeters B. 6 meters C. 2 meters D. 70 centimeters T3C08 (D) What causes tropospheric ducting? A. Discharges of lightning during electrical storms B. Sunspots and solar flares C. Updrafts from hurricanes and tornadoes D. Temperature inversions in the atmosphere T3C09 (A) What is generally the best time for long-distance 10 meter band propagation via the F region? A. From dawn to shortly after sunset during periods of high sunspot activity B. From shortly after sunset to dawn during periods of high sunspot activity C. From dawn to shortly after sunset during periods of low sunspot activity D. From shortly after sunset to dawn during periods of low sunspot activity T3C10 (A) Which of the following bands may provide long-distance communications via the ionosphere’s F region during the peak of the sunspot cycle? A. 6 and 10 meters B. 23 centimeters C. 70 centimeters and 1.25 meters D. All these choices are correct T3C11 (C) Why is the radio horizon for VHF and UHF signals more distant than the visual horizon? A. Radio signals move somewhat faster than the speed of light B. Radio waves are not blocked by dust particles C. The atmosphere refracts radio waves slightly D. Radio waves are blocked by dust particles T4A01 (D) Which of the following is an appropriate power supply rating for a typical 50 watt output mobile FM transceiver? A. 24.0 volts at 4 amperes B. 13.8 volts at 4 amperes C. 24.0 volts at 12 amperes D. 13.8 volts at 12 amperes T4A02 (A) Which of the following should be considered when selecting an accessory SWR meter? A. The frequency and power level at which the measurements will be made B. The distance that the meter will be located from the antenna C. The types of modulation being used at the station D. All these choices are correct T4A03 (A) Why are short, heavy-gauge wires used for a transceiver’s DC power connection? A. To minimize voltage drop when transmitting B. To provide a good counterpoise for the antenna C. To avoid RF interference D. All these choices are correct T4A04 (B) How are the transceiver audio input and output connected in a station configured to operate using FT8? A. To a computer running a terminal program and connected to a terminal node controller unit B. To the audio input and output of a computer running WSJT-X software C. To an FT8 conversion unit, a keyboard, and a computer monitor D. To a computer connected to the FT8converter.com website T4A05 (A) Where should an RF power meter be installed? A. In the feed line, between the transmitter and antenna B. At the power supply output C. In parallel with the push-to-talk line and the antenna D. In the power supply cable, as close as possible to the radio T4A06 (C) What signals are used in a computer-radio interface for digital mode operation? A. Receive and transmit mode, status, and location B. Antenna and RF power C. Receive audio, transmit audio, and transmitter keying D. NMEA GPS location and DC power T4A07 (C) Which of the following connections is made between a computer and a transceiver to use computer software when operating digital modes? A. Computer “line out” to transceiver push-to-talk B. Computer “line in” to transceiver push-to-talk C. Computer “line in” to transceiver speaker connector D. Computer “line out” to transceiver speaker connector T4A08 (D) Which of the following conductors is preferred for bonding at RF? A. Copper braid removed from coaxial cable B. Steel wire C. Twisted-pair cable D. Flat copper strap T4A09 (B) How can you determine the length of time that equipment can be powered from a battery? A. Divide the watt-hour rating of the battery by the peak power consumption of the equipment B. Divide the battery ampere-hour rating by the average current draw of the equipment C. Multiply the watts per hour consumed by the equipment by the battery power rating D. Multiply the square of the current rating of the battery by the input resistance of the equipment T4A10 (A) What function is performed with a transceiver and a digital mode hot spot? A. Communication using digital voice or data systems via the internet B. FT8 digital communications via AFSK C. RTTY encoding and decoding without a computer D. High-speed digital communications for meteor scatter T4A11 (A) Where should the negative power return of a mobile transceiver be connected in a vehicle? A. At the 12 volt battery chassis ground B. At the antenna mount C. To any metal part of the vehicle D. Through the transceiver’s mounting bracket T4A12 (C) What is an electronic keyer? A. A device for switching antennas from transmit to receive B. A device for voice activated switching from receive to transmit C. A device that assists in manual sending of Morse code D. An interlock to prevent unauthorized use of a radio T4B01 (B) What is the effect of excessive microphone gain on SSB transmissions? A. Frequency instability B. Distorted transmitted audio C. Increased SWR D. All these choices are correct T4B02 (A) Which of the following can be used to enter a transceiver’s operating frequency? A. The keypad or VFO knob B. The CTCSS or DTMF encoder C. The Automatic Frequency Control D. All these choices are correct T4B03 (A) How is squelch adjusted so that a weak FM signal can be heard? A. Set the squelch threshold so that receiver output audio is on all the time B. Turn up the audio level until it overcomes the squelch threshold C. Turn on the anti-squelch function D. Enable squelch enhancement T4B04 (B) What is a way to enable quick access to a favorite frequency or channel on your transceiver? A. Enable the frequency offset B. Store it in a memory channel C. Enable the VOX D. Use the scan mode to select the desired frequency T4B05 (C) What does the scanning function of an FM transceiver do? A. Checks incoming signal deviation B. Prevents interference to nearby repeaters C. Tunes through a range of frequencies to check for activity D. Checks for messages left on a digital bulletin board T4B06 (D) Which of the following controls could be used if the voice pitch of a single-sideband signal returning to your CQ call seems too high or low? A. The AGC or limiter B. The bandwidth selection C. The tone squelch D. The RIT or Clarifier T4B07 (B) What does a DMR “code plug” contain? A. Your call sign in CW for automatic identification B. Access information for repeaters and talkgroups C. The codec for digitizing audio D. The DMR software version T4B08 (B) What is the advantage of having multiple receive bandwidth choices on a multimode transceiver? A. Permits monitoring several modes at once by selecting a separate filter for each mode B. Permits noise or interference reduction by selecting a bandwidth matching the mode C. Increases the number of frequencies that can be stored in memory D. Increases the amount of offset between receive and transmit frequencies T4B09 (C) How is a specific group of stations selected on a digital voice transceiver? A. By retrieving the frequencies from transceiver memory B. By enabling the group’s CTCSS tone C. By entering the group’s identification code D. By activating automatic identification T4B10 (C) Which of the following receiver filter bandwidths provides the best signal-to-noise ratio for SSB reception? A. 500 Hz B. 1000 Hz C. 2400 Hz D. 5000 Hz T4B11 (A) Which of the following must be programmed into a D-STAR digital transceiver before transmitting? A. Your call sign B. Your output power C. The codec type being used D. All these choices are correct T4B12 (D) What is the result of tuning an FM receiver above or below a signal’s frequency? A. Change in audio pitch B. Sideband inversion C. Generation of a heterodyne tone D. Distortion of the signal’s audio T5A01 (D) Electrical current is measured in which of the following units? A. Volts B. Watts C. Ohms D. Amperes T5A02 (B) Electrical power is measured in which of the following units? A. Volts B. Watts C. Watt-hours D. Amperes T5A03 (D) What is the name for the flow of electrons in an electric circuit? A. Voltage B. Resistance C. Capacitance D. Current T5A04 (C) What are the units of electrical resistance? A. Siemens B. Mhos C. Ohms D. Coulombs T5A05 (A) What is the electrical term for the force that causes electron flow? A. Voltage B. Ampere-hours C. Capacitance D. Inductance T5A06 (A) What is the unit of frequency? A. Hertz B. Henry C. Farad D. Tesla T5A07 (B) Why are metals generally good conductors of electricity? A. They have relatively high density B. They have many free electrons C. They have many free protons D. All these choices are correct T5A08 (B) Which of the following is a good electrical insulator? A. Copper B. Glass C. Aluminum D. Mercury T5A09 (C) Which of the following describes alternating current? A. Current that alternates between a positive direction and zero B. Current that alternates between a negative direction and zero C. Current that alternates between positive and negative directions D. All these answers are correct T5A10 (C) Which term describes the rate at which electrical energy is used? A. Resistance B. Current C. Power D. Voltage T5A11 (D) What type of current flow is opposed by resistance? A. Direct current B. Alternating current C. RF current D. All these choices are correct T5A12 (D) What describes the number of times per second that an alternating current makes a complete cycle? A. Pulse rate B. Speed C. Wavelength D. Frequency T5B01 (C) How many milliamperes is 1.5 amperes? A. 15 milliamperes B. 150 milliamperes C. 1500 milliamperes D. 15,000 milliamperes T5B02 (A) Which is equal to 1,500,000 hertz? A. 1500 kHz B. 1500 MHz C. 15 GHz D. 150 kHz T5B03 (C) Which is equal to one kilovolt? A. One one-thousandth of a volt B. One hundred volts C. One thousand volts D. One million volts T5B04 (A) Which is equal to one microvolt? A. One one-millionth of a volt B. One million volts C. One thousand kilovolts D. One one-thousandth of a volt T5B05 (B) Which is equal to 500 milliwatts? A. 0.02 watts B. 0.5 watts C. 5 watts D. 50 watts T5B06 (D) Which is equal to 3000 milliamperes? A. 0.003 amperes B. 0.3 amperes C. 3,000,000 amperes D. 3 amperes T5B07 (C) Which is equal to 3.525 MHz? A. 0.003525 kHz B. 35.25 kHz C. 3525 kHz D. 3,525,000 kHz T5B08 (B) Which is equal to 1,000,000 picofarads? A. 0.001 microfarads B. 1 microfarad C. 1000 microfarads D. 1,000,000,000 microfarads T5B09 (B) Which decibel value most closely represents a power increase from 5 watts to 10 watts? A. 2 dB B. 3 dB C. 5 dB D. 10 dB T5B10 (C) Which decibel value most closely represents a power decrease from 12 watts to 3 watts? A. -1 dB B. -3 dB C. -6 dB D. -9 dB T5B11 (A) Which decibel value represents a power increase from 20 watts to 200 watts? A. 10 dB B. 12 dB C. 18 dB D. 28 dB T5B12 (D) Which is equal to 28400 kHz? A. 28.400 kHz B. 2.800 MHz C. 284.00 MHz D. 28.400 MHz T5B13 (C) Which is equal to 2425 MHz? A. 0.002425 GHz B. 24.25 GHz C. 2.425 GHz D. 2425 GHz T5C01 (D) What describes the ability to store energy in an electric field? A. Inductance B. Resistance C. Tolerance D. Capacitance T5C02 (A) What is the unit of capacitance? A. The farad B. The ohm C. The volt D. The henry T5C03 (D) What describes the ability to store energy in a magnetic field? A. Admittance B. Capacitance C. Resistance D. Inductance T5C04 (C) What is the unit of inductance? A. The coulomb B. The farad C. The henry D. The ohm T5C05 (D) What is the unit of impedance? A. The volt B. The ampere C. The coulomb D. The ohm T5C06 (A) What does the abbreviation “RF” mean? A. Radio frequency signals of all types B. The resonant frequency of a tuned circuit C. The real frequency transmitted as opposed to the apparent frequency D. Reflective force in antenna transmission lines T5C07 (D) What is the abbreviation for megahertz? A. MH B. mh C. Mhz D. MHz T5C08 (A) What is the formula used to calculate electrical power (P) in a DC circuit? A. P = I ? E B. P = E / I C. P = E – I D. P = I + E T5C09 (A) How much power is delivered by a voltage of 13.8 volts DC and a current of 10 amperes? A. 138 watts B. 0.7 watts C. 23.8 watts D. 3.8 watts T5C10 (B) How much power is delivered by a voltage of 12 volts DC and a current of 2.5 amperes? A. 4.8 watts B. 30 watts C. 14.5 watts D. 0.208 watts T5C11 (B) How much current is required to deliver 120 watts at a voltage of 12 volts DC? A. 0.1 amperes B. 10 amperes C. 12 amperes D. 132 amperes T5C12 (A) What is impedance? A. The opposition to AC current flow B. The inverse of resistance C. The Q or Quality Factor of a component D. The power handling capability of a component T5C13 (D) What is the abbreviation for kilohertz? A. KHZ B. khz C. khZ D. kHz T5D01 (B) What formula is used to calculate current in a circuit? A. I = E ? R B. I = E / R C. I = E + R D. I = E - R T5D02 (A) What formula is used to calculate voltage in a circuit? A. E = I x R B. E = I / R C. E = I + R D. E = I - R T5D03 (B) What formula is used to calculate resistance in a circuit? A. R = E x I B. R = E / I C. R = E + I D. R = E - I T5D04 (B) What is the resistance of a circuit in which a current of 3 amperes flows when connected to 90 volts? A. 3 ohms B. 30 ohms C. 93 ohms D. 270 ohms T5D05 (C) What is the resistance of a circuit for which the applied voltage is 12 volts and the current flow is 1.5 amperes? A. 18 ohms B. 0.125 ohms C. 8 ohms D. 13.5 ohms T5D06 (A) What is the resistance of a circuit that draws 4 amperes from a 12-volt source? A. 3 ohms B. 16 ohms C. 48 ohms D. 8 ohms T5D07 (D) What is the current in a circuit with an applied voltage of 120 volts and a resistance of 80 ohms? A. 9600 amperes B. 200 amperes C. 0.667 amperes D. 1.5 amperes T5D08 (C) What is the current through a 100-ohm resistor connected across 200 volts? A. 20,000 amperes B. 0.5 amperes C. 2 amperes D. 100 amperes T5D09 (C) What is the current through a 24-ohm resistor connected across 240 volts? A. 24,000 amperes B. 0.1 amperes C. 10 amperes D. 216 amperes T5D10 (A) What is the voltage across a 2-ohm resistor if a current of 0.5 amperes flows through it? A. 1 volt B. 0.25 volts C. 2.5 volts D. 1.5 volts T5D11 (B) What is the voltage across a 10-ohm resistor if a current of 1 ampere flows through it? A. 1 volt B. 10 volts C. 11 volts D. 9 volts T5D12 (D) What is the voltage across a 10-ohm resistor if a current of 2 amperes flows through it? A. 8 volts B. 0.2 volts C. 12 volts D. 20 volts T5D13 (A) In which type of circuit is DC current the same through all components? A. Series B. Parallel C. Resonant D. Branch T5D14 (B) In which type of circuit is voltage the same across all components? A. Series B. Parallel C. Resonant D. Branch T6A01 (B) What electrical component opposes the flow of current in a DC circuit? A. Inductor B. Resistor C. Inverter D. Transformer T6A02 (C) What type of component is often used as an adjustable volume control? A. Fixed resistor B. Power resistor C. Potentiometer D. Transformer T6A03 (B) What electrical parameter is controlled by a potentiometer? A. Inductance B. Resistance C. Capacitance D. Field strength T6A04 (B) What electrical component stores energy in an electric field? A. Varistor B. Capacitor C. Inductor D. Diode T6A05 (D) What type of electrical component consists of conductive surfaces separated by an insulator? A. Resistor B. Potentiometer C. Oscillator D. Capacitor T6A06 (C) What type of electrical component stores energy in a magnetic field? A. Varistor B. Capacitor C. Inductor D. Diode T6A07 (D) What electrical component is typically constructed as a coil of wire? A. Switch B. Capacitor C. Diode D. Inductor T6A08 (C) What is the function of an SPDT switch? A. A single circuit is opened or closed B. Two circuits are opened or closed C. A single circuit is switched between one of two other circuits D. Two circuits are each switched between one of two other circuits T6A09 (A) What electrical component is used to protect other circuit components from current overloads? A. Fuse B. Thyratron C. Varactor D. All these choices are correct T6A10 (D) Which of the following battery chemistries is rechargeable? A. Nickel-metal hydride B. Lithium-ion C. Lead-acid D. All these choices are correct T6A11 (B) Which of the following battery chemistries is not rechargeable? A. Nickel-cadmium B. Carbon-zinc C. Lead-acid D. Lithium-ion T6A12(A) What type of switch is represented by component 3 in figure T-2? A. Single-pole single-throw B. Single-pole double-throw C. Double-pole single-throw D. Double-pole double-throw T6B01 (A) Which is true about forward voltage drop in a diode? A. It is lower in some diode types than in others B. It is proportional to peak inverse voltage C. It indicates that the diode is defective D. It has no impact on the voltage delivered to the load T6B02 (C) What electronic component allows current to flow in only one direction? A. Resistor B. Fuse C. Diode D. Driven element T6B03 (C) Which of these components can be used as an electronic switch? A. Varistor B. Potentiometer C. Transistor D. Thermistor T6B04 (B) Which of the following components can consist of three regions of semiconductor material? A. Alternator B. Transistor C. Triode D. Pentagrid converter T6B05 (B) What type of transistor has a gate, drain, and source? A. Varistor B. Field-effect C. Tesla-effect D. Bipolar junction T6B06 (B) How is the cathode lead of a semiconductor diode often marked on the package? A. With the word "cathode" B. With a stripe C. With the letter C D. With the letter K T6B07 (A) What causes a light-emitting diode (LED) to emit light? A. Forward current B. Reverse current C. Capacitively-coupled RF signal D. Inductively-coupled RF signal T6B08 (D) What does the abbreviation FET stand for? A. Frequency Emission Transmitter B. Fast Electron Transistor C. Free Electron Transmitter D. Field Effect Transistor T6B09 (C) What are the names for the electrodes of a diode? A. Plus and minus B. Source and drain C. Anode and cathode D. Gate and base T6B10 (B) Which of the following can provide power gain? A. Transformer B. Transistor C. Reactor D. Resistor T6B11 (A) What is the term that describes a device's ability to amplify a signal? A. Gain B. Forward resistance C. Forward voltage drop D. On resistance T6B12 (B) What are the names of the electrodes of a bipolar junction transistor? A. Signal, bias, power B. Emitter, base, collector C. Input, output, supply D. Pole one, pole two, output T6C01 (C) What is the name of an electrical wiring diagram that uses standard component symbols? A. Bill of materials B. Connector pinout C. Schematic D. Flow chart T6C02 (A) What is component 1 in figure T-1? A. Resistor B. Transistor C. Battery D. Connector T6C03 (B) What is component 2 in figure T-1? A. Resistor B. Transistor C. Indicator lamp D. Connector T6C04 (C) What is component 3 in figure T-1? A. Resistor B. Transistor C. Lamp D. Ground symbol T6C05 (D) What is component 4 in figure T-1? A. Resistor B. Transistor C. Ground symbol D. Battery T6C06 (B) What is component 6 in figure T-2? A. Resistor B. Capacitor C. Regulator IC D. Transistor T6C07 (D) What is component 8 in figure T-2? A. Resistor B. Inductor C. Regulator IC D. Light emitting diode T6C08 (C) What is component 9 in figure T-2? A. Variable capacitor B. Variable inductor C. Variable resistor D. Variable transformer T6C09 (D) What is component 4 in figure T-2? A. Variable inductor B. Double-pole switch C. Potentiometer D. Transformer T6C10 (D) What is component 3 in figure T-3? A. Connector B. Meter C. Variable capacitor D. Variable inductor T6C11 (A) What is component 4 in figure T-3? A. Antenna B. Transmitter C. Dummy load D. Ground T6C12 (C) Which of the following is accurately represented in electrical schematics? A. Wire lengths B. Physical appearance of components C. Component connections D. All these choices are correct T6D01 (B) Which of the following devices or circuits changes an alternating current into a varying direct current signal? A. Transformer B. Rectifier C. Amplifier D. Reflector T6D02 (A) What is a relay? A. An electrically-controlled switch B. A current controlled amplifier C. An inverting amplifier D. A pass transistor T6D03 (C) Which of the following is a reason to use shielded wire? A. To decrease the resistance of DC power connections B. To increase the current carrying capability of the wire C. To prevent coupling of unwanted signals to or from the wire D. To couple the wire to other signals T6D04 (C) Which of the following displays an electrical quantity as a numeric value? A. Potentiometer B. Transistor C. Meter D. Relay T6D05 (A) What type of circuit controls the amount of voltage from a power supply? A. Regulator B. Oscillator C. Filter D. Phase inverter T6D06 (B) What component changes 120 V AC power to a lower AC voltage for other uses? A. Variable capacitor B. Transformer C. Transistor D. Diode T6D07 (A) Which of the following is commonly used as a visual indicator? A. LED B. FET C. Zener diode D. Bipolar transistor T6D08 (D) Which of the following is combined with an inductor to make a resonant circuit? A. Resistor B. Zener diode C. Potentiometer D. Capacitor T6D09 (C) What is the name of a device that combines several semiconductors and other components into one package? A. Transducer B. Multi-pole relay C. Integrated circuit D. Transformer T6D10 (C) What is the function of component 2 in figure T-1? A. Give off light when current flows through it B. Supply electrical energy C. Control the flow of current D. Convert electrical energy into radio waves T6D11 (A) Which of the following is a resonant or tuned circuit? A. An inductor and a capacitor in series or parallel B. A linear voltage regulator C. A resistor circuit used for reducing standing wave ratio D. A circuit designed to provide high-fidelity audio T7A01 (B) Which term describes the ability of a receiver to detect the presence of a signal? A. Linearity B. Sensitivity C. Selectivity D. Total Harmonic Distortion T7A02 (A) What is a transceiver? A. A device that combines a receiver and transmitter B. A device for matching feed line impedance to 50 ohms C. A device for automatically sending and decoding Morse code D. A device for converting receiver and transmitter frequencies to another band T7A03 (B) Which of the following is used to convert a signal from one frequency to another? A. Phase splitter B. Mixer C. Inverter D. Amplifier T7A04 (C) Which term describes the ability of a receiver to discriminate between multiple signals? A. Discrimination ratio B. Sensitivity C. Selectivity D. Harmonic distortion T7A05 (D) What is the name of a circuit that generates a signal at a specific frequency? A. Reactance modulator B. Phase modulator C. Low-pass filter D. Oscillator T7A06 (C) What device converts the RF input and output of a transceiver to another band? A. High-pass filter B. Low-pass filter C. Transverter D. Phase converter T7A07 (B) What is the function of a transceiver’s PTT input? A. Input for a key used to send CW B. Switches transceiver from receive to transmit when grounded C. Provides a transmit tuning tone when grounded D. Input for a preamplifier tuning tone T7A08 (C) Which of the following describes combining speech with an RF carrier signal? A. Impedance matching B. Oscillation C. Modulation D. Low-pass filtering T7A09 (B) What is the function of the SSB/CW-FM switch on a VHF power amplifier? A. Change the mode of the transmitted signal B. Set the amplifier for proper operation in the selected mode C. Change the frequency range of the amplifier to operate in the proper segment of the band D. Reduce the received signal noise T7A10 (B) What device increases the transmitted output power from a transceiver? A. A voltage divider B. An RF power amplifier C. An impedance network D. All these choices are correct T7A11 (A) Where is an RF preamplifier installed? A. Between the antenna and receiver B. At the output of the transmitter power amplifier C. Between the transmitter and the antenna tuner D. At the output of the receiver audio amplifier T7B01 (D) What can you do if you are told your FM handheld or mobile transceiver is over-deviating? A. Talk louder into the microphone B. Let the transceiver cool off C. Change to a higher power level D. Talk farther away from the microphone T7B02 (A) What would cause a broadcast AM or FM radio to receive an amateur radio transmission unintentionally? A. The receiver is unable to reject strong signals outside the AM or FM band B. The microphone gain of the transmitter is turned up too high C. The audio amplifier of the transmitter is overloaded D. The deviation of an FM transmitter is set too low T7B03 (D) Which of the following can cause radio frequency interference? A. Fundamental overload B. Harmonics C. Spurious emissions D. All these choices are correct T7B04 (D) Which of the following could you use to cure distorted audio caused by RF current on the shield of a microphone cable? A. Band-pass filter B. Low-pass filter C. Preamplifier D. Ferrite choke T7B05 (A) How can fundamental overload of a non-amateur radio or TV receiver by an amateur signal be reduced or eliminated? A. Block the amateur signal with a filter at the antenna input of the affected receiver B. Block the interfering signal with a filter on the amateur transmitter C. Switch the transmitter from FM to SSB D. Switch the transmitter to a narrow-band mode T7B06 (A) Which of the following actions should you take if a neighbor tells you that your station’s transmissions are interfering with their radio or TV reception? A. Make sure that your station is functioning properly and that it does not cause interference to your own radio or television when it is tuned to the same channel B. Immediately turn off your transmitter and contact the nearest FCC office for assistance C. Install a harmonic doubler on the output of your transmitter and tune it until the interference is eliminated D. All these choices are correct T7B07 (D) Which of the following can reduce overload of a VHF transceiver by a nearby commercial FM station? A. Installing an RF preamplifier B. Using double-shielded coaxial cable C. Installing bypass capacitors on the microphone cable D. Installing a band-reject filter T7B08 (D) What should you do if something in a neighbor’s home is causing harmful interference to your amateur station? A. Work with your neighbor to identify the offending device B. Politely inform your neighbor that FCC rules prohibit the use of devices that cause interference C. Make sure your station meets the standards of good amateur practice D. All these choices are correct T7B09 (D) What should be the first step to resolve non-fiber optic cable TV interference caused by your amateur radio transmission? A. Add a low-pass filter to the TV antenna input B. Add a high-pass filter to the TV antenna input C. Add a preamplifier to the TV antenna input D. Be sure all TV feed line coaxial connectors are installed properly T7B10 (D) What might be a problem if you receive a report that your audio signal through an FM repeater is distorted or unintelligible? A. Your transmitter is slightly off frequency B. Your batteries are running low C. You are in a bad location D. All these choices are correct T7B11 (C) What is a symptom of RF feedback in a transmitter or transceiver? A. Excessive SWR at the antenna connection B. The transmitter will not stay on the desired frequency C. Reports of garbled, distorted, or unintelligible voice transmissions D. Frequent blowing of power supply fuses T7C01 (A) What is the primary purpose of a dummy load? A. To prevent transmitting signals over the air when making tests B. To prevent over-modulation of a transmitter C. To improve the efficiency of an antenna D. To improve the signal-to-noise ratio of a receiver T7C02 (B) Which of the following is used to determine if an antenna is resonant at the desired operating frequency? A. A VTVM B. An antenna analyzer C. A Q meter D. A frequency counter T7C03 (B) What does a dummy load consist of? A. A high-gain amplifier and a TR switch B. A non-inductive resistor mounted on a heat sink C. A low-voltage power supply and a DC relay D. A 50-ohm reactance used to terminate a transmission line T7C04 (C) What reading on an SWR meter indicates a perfect impedance match between the antenna and the feed line? A. 50:50 B. Zero C. 1:1 D. Full Scale T7C05 (A) Why do most solid-state transmitters reduce output power as SWR increases beyond a certain level? A. To protect the output amplifier transistors B. To comply with FCC rules on spectral purity C. Because power supplies cannot supply enough current at high SWR D. To lower the SWR on the transmission line T7C06 (D) What does an SWR reading of 4:1 indicate? A. Loss of -4 dB B. Good impedance match C. Gain of +4 dB D. Impedance mismatch T7C07 (C) What happens to power lost in a feed line? A. It increases the SWR B. It is radiated as harmonics C. It is converted into heat D. It distorts the signal T7C08 (D) Which instrument can be used to determine SWR? A. Voltmeter B. Ohmmeter C. Iambic pentameter D. Directional wattmeter T7C09 (A) Which of the following causes failure of coaxial cables? A. Moisture contamination B. Solder flux contamination C. Rapid fluctuation in transmitter output power D. Operation at 100% duty cycle for an extended period T7C10 (D) Why should the outer jacket of coaxial cable be resistant to ultraviolet light? A. Ultraviolet resistant jackets prevent harmonic radiation B. Ultraviolet light can increase losses in the cable’s jacket C. Ultraviolet and RF signals can mix, causing interference D. Ultraviolet light can damage the jacket and allow water to enter the cable T7C11 (C) What is a disadvantage of air core coaxial cable when compared to foam or solid dielectric types? A. It has more loss per foot B. It cannot be used for VHF or UHF antennas C. It requires special techniques to prevent moisture in the cable D. It cannot be used at below freezing temperatures T7D01 (B) Which instrument would you use to measure electric potential? A. An ammeter B. A voltmeter C. A wavemeter D. An ohmmeter T7D02 (B) How is a voltmeter connected to a component to measure applied voltage? A. In series B. In parallel C. In quadrature D. In phase T7D03 (A) When configured to measure current, how is a multimeter connected to a component? A. In series B. In parallel C. In quadrature D. In phase T7D04 (D) Which instrument is used to measure electric current? A. An ohmmeter B. An electrometer C. A voltmeter D. An ammeter T7D06 (C) Which of the following can damage a multimeter? A. Attempting to measure resistance using the voltage setting B. Failing to connect one of the probes to ground C. Attempting to measure voltage when using the resistance setting D. Not allowing it to warm up properly T7D07 (C) Which of the following measurements are made using a multimeter? A. Signal strength and noise B. Impedance and reactance C. Voltage and resistance D. All these choices are correct T7D08 (A) Which of the following types of solder should not be used for radio and electronic applications? A. Acid-core solder B. Lead-tin solder C. Rosin-core solder D. Tin-copper solder T7D09 (C) What is the characteristic appearance of a cold tin-lead solder joint? A. Dark black spots B. A bright or shiny surface C. A rough or lumpy surface D. Excessive solder T7D10 (A) What reading indicates that an ohmmeter is connected across a large, discharged capacitor? A. Increasing resistance with time B. Decreasing resistance with time C. Steady full-scale reading D. Alternating between open and short circuit T7D11 (B) Which of the following precautions should be taken when measuring in-circuit resistance with an ohmmeter? A. Ensure that the applied voltages are correct B. Ensure that the circuit is not powered C. Ensure that the circuit is grounded D. Ensure that the circuit is operating at the correct frequency T8A01 (C) Which of the following is a form of amplitude modulation? A. Spread spectrum B. Packet radio C. Single sideband D. Phase shift keying (PSK) T8A02 (A) What type of modulation is commonly used for VHF packet radio transmissions? A. FM or PM B. SSB C. AM D. PSK T8A03 (C) Which type of voice mode is often used for long-distance (weak signal) contacts on the VHF and UHF bands? A. FM B. DRM C. SSB D. PM T8A04 (D) Which type of modulation is commonly used for VHF and UHF voice repeaters? A. AM B. SSB C. PSK D. FM or PM T8A05 (C) Which of the following types of signal has the narrowest bandwidth? A. FM voice B. SSB voice C. CW D. Slow-scan TV T8A06 (A) Which sideband is normally used for 10 meter HF, VHF, and UHF single-sideband communications? A. Upper sideband B. Lower sideband C. Suppressed sideband D. Inverted sideband T8A07 (C) What is a characteristic of single sideband (SSB) compared to FM? A. SSB signals are easier to tune in correctly B. SSB signals are less susceptible to interference C. SSB signals have narrower bandwidth D. All these choices are correct T8A08 (B) What is the approximate bandwidth of a typical single sideband (SSB) voice signal? A. 1 kHz B. 3 kHz C. 6 kHz D. 15 kHz T8A09 (C) What is the approximate bandwidth of a VHF repeater FM voice signal? A. Less than 500 Hz B. About 150 kHz C. Between 10 and 15 kHz D. Between 50 and 125 kHz T8A10 (B) What is the approximate bandwidth of AM fast-scan TV transmissions? A. More than 10 MHz B. About 6 MHz C. About 3 MHz D. About 1 MHz T8A11 (B) What is the approximate bandwidth required to transmit a CW signal? A. 2.4 kHz B. 150 Hz C. 1000 Hz D. 15 kHz T8A12 (B) Which of the following is a disadvantage of FM compared with single sideband? A. Voice quality is poorer B. Only one signal can be received at a time C. FM signals are harder to tune D. All these choices are correct T8B01 (C) What telemetry information is typically transmitted by satellite beacons? A. The signal strength of received signals B. Time of day accurate to plus or minus 1/10 second C. Health and status of the satellite D. All these choices are correct T8B02 (B) What is the impact of using excessive effective radiated power on a satellite uplink? A. Possibility of commanding the satellite to an improper mode B. Blocking access by other users C. Overloading the satellite batteries D. Possibility of rebooting the satellite control computer T8B03 (D) Which of the following are provided by satellite tracking programs? A. Maps showing the real-time position of the satellite track over Earth B. The time, azimuth, and elevation of the start, maximum altitude, and end of a pass C. The apparent frequency of the satellite transmission, including effects of Doppler shift D. All these choices are correct T8B04 (D) What mode of transmission is commonly used by amateur radio satellites? A. SSB B. FM C. CW/data D. All these choices are correct T8B05 (D) What is a satellite beacon? A. The primary transmit antenna on the satellite B. An indicator light that shows where to point your antenna C. A reflective surface on the satellite D. A transmission from a satellite that contains status information T8B06 (B) Which of the following are inputs to a satellite tracking program? A. The satellite transmitted power B. The Keplerian elements C. The last observed time of zero Doppler shift D. All these choices are correct T8B07 (C) What is Doppler shift in reference to satellite communications? A. A change in the satellite orbit B. A mode where the satellite receives signals on one band and transmits on another C. An observed change in signal frequency caused by relative motion between the satellite and Earth station D. A special digital communications mode for some satellites T8B08 (B) What is meant by the statement that a satellite is operating in U/V mode? A. The satellite uplink is in the 15 meter band and the downlink is in the 10 meter band B. The satellite uplink is in the 70 centimeter band and the downlink is in the 2 meter band C. The satellite operates using ultraviolet frequencies D. The satellite frequencies are usually variable T8B09 (B) What causes spin fading of satellite signals? A. Circular polarized noise interference radiated from the sun B. Rotation of the satellite and its antennas C. Doppler shift of the received signal D. Interfering signals within the satellite uplink band T8B10 (D) What is a LEO satellite? A. A sun synchronous satellite B. A highly elliptical orbit satellite C. A satellite in low energy operation mode D. A satellite in low earth orbit T8B11 (A) Who may receive telemetry from a space station? A. Anyone B. A licensed radio amateur with a transmitter equipped for interrogating the satellite C. A licensed radio amateur who has been certified by the protocol developer D. A licensed radio amateur who has registered for an access code from AMSAT T8B12 (C) Which of the following is a way to determine whether your satellite uplink power is neither too low nor too high? A. Check your signal strength report in the telemetry data B. Listen for distortion on your downlink signal C. Your signal strength on the downlink should be about the same as the beacon D. All these choices are correct T8C01 (C) Which of the following methods is used to locate sources of noise interference or jamming? A. Echolocation B. Doppler radar C. Radio direction finding D. Phase locking T8C02 (B) Which of these items would be useful for a hidden transmitter hunt? A. Calibrated SWR meter B. A directional antenna C. A calibrated noise bridge D. All these choices are correct T8C03 (D) What operating activity involves contacting as many stations as possible during a specified period? A. Simulated emergency exercises B. Net operations C. Public service events D. Contesting T8C04 (C) Which of the following is good procedure when contacting another station in a contest? A. Sign only the last two letters of your call if there are many other stations calling B. Contact the station twice to be sure that you are in his log C. Send only the minimum information needed for proper identification and the contest exchange D. All these choices are correct T8C05 (A) What is a grid locator? A. A letter-number designator assigned to a geographic location B. A letter-number designator assigned to an azimuth and elevation C. An instrument for neutralizing a final amplifier D. An instrument for radio direction finding T8C06 (B) How is over the air access to IRLP nodes accomplished? A. By obtaining a password that is sent via voice to the node B. By using DTMF signals C. By entering the proper internet password D. By using CTCSS tone codes T8C07 (D) What is Voice Over Internet Protocol (VoIP)? A. A set of rules specifying how to identify your station when linked over the internet to another station B. A technique employed to “spot” DX stations via the internet C. A technique for measuring the modulation quality of a transmitter using remote sites monitored via the internet D. A method of delivering voice communications over the internet using digital techniques T8C08 (A) What is the Internet Radio Linking Project (IRLP)? A. A technique to connect amateur radio systems, such as repeaters, via the internet using Voice Over Internet Protocol (VoIP) B. A system for providing access to websites via amateur radio C. A system for informing amateurs in real time of the frequency of active DX stations D. A technique for measuring signal strength of an amateur transmitter via the internet T8C09 (D) Which of the following protocols enables an amateur station to transmit through a repeater without using a radio to initiate the transmission? A. IRLP B. D-STAR C. DMR D. EchoLink T8C10 (C) What is required before using the EchoLink system? A. Complete the required EchoLink training B. Purchase a license to use the EchoLink software C. Register your call sign and provide proof of license D. All these choices are correct T8C11 (A) What is an amateur radio station that connects other amateur stations to the internet? A. A gateway B. A repeater C. A digipeater D. A beacon T8D01 (D) Which of the following is a digital communications mode? A. Packet radio B. IEEE 802.11 C. FT8 D. All these choices are correct T8D02 (B) What is a “talkgroup” on a DMR repeater? A. A group of operators sharing common interests B. A way for groups of users to share a channel at different times without hearing other users on the channel C. A protocol that increases the signal-to-noise ratio when multiple repeaters are linked together D. A net that meets at a specified time T8D03 (D) What kind of data can be transmitted by APRS? A. GPS position data B. Text messages C. Weather data D. All these choices are correct T8D04 (C) What type of transmission is indicated by the term "NTSC?" A. A Normal Transmission mode in Static Circuit B. A special mode for satellite uplink C. An analog fast-scan color TV signal D. A frame compression scheme for TV signals T8D05 (A) Which of the following is an application of APRS? A. Providing real-time tactical digital communications in conjunction with a map showing the locations of stations B. Showing automatically the number of packets transmitted via PACTOR during a specific time interval C. Providing voice over internet connection between repeaters D. Providing information on the number of stations signed into a repeater T8D06 (B) What does the abbreviation "PSK" mean? A. Pulse Shift Keying B. Phase Shift Keying C. Packet Short Keying D. Phased Slide Keying T8D07 (A) Which of the following describes DMR? A. A technique for time-multiplexing two digital voice signals on a single 12.5 kHz repeater channel B. An automatic position tracking mode for FM mobiles communicating through repeaters C. An automatic computer logging technique for hands-off logging when communicating while operating a vehicle D. A digital technique for transmitting on two repeater inputs simultaneously for automatic error correction T8D08 (D) Which of the following is included in packet radio transmissions? A. A check sum that permits error detection B. A header that contains the call sign of the station to which the information is being sent C. Automatic repeat request in case of error D. All these choices are correct T8D09 (D) What is CW? A. A type of electromagnetic propagation B. A digital mode used primarily on 2 meter FM C. A technique for coil winding D. Another name for a Morse code transmission T8D10 (D) Which of the following operating activities is supported by digital mode software in the WSJT-X software suite? A. Earth-Moon-Earth B. Weak signal propagation beacons C. Meteor scatter D. All these choices are correct T8D11 (C) What is an ARQ transmission system? A. A special transmission format limited to video signals B. A system used to encrypt command signals to an amateur radio satellite C. An error correction method in which the receiving station detects errors and sends a request for retransmission D. A method of compressing data using autonomous reiterative Q codes prior to final encoding T8D12 (A) Which of the following best describes an amateur radio mesh network? A. An amateur-radio based data network using commercial Wi-Fi equipment with modified firmware B. A wide-bandwidth digital voice mode employing DMR protocols C. A satellite communications network using modified commercial satellite TV hardware D. An internet linking protocol used to network repeaters T8D13 (B) What is FT8? A. A wideband FM voice mode B. A digital mode capable of low signal-to-noise operation C. An eight channel multiplex mode for FM repeaters D. A digital slow-scan TV mode with forward error correction and automatic color compensation T9A01 (C) What is a beam antenna? A. An antenna built from aluminum I-beams B. An omnidirectional antenna invented by Clarence Beam C. An antenna that concentrates signals in one direction D. An antenna that reverses the phase of received signals T9A02 (A) Which of the following describes a type of antenna loading? A. Electrically lengthening by inserting inductors in radiating elements B. Inserting a resistor in the radiating portion of the antenna to make it resonant C. Installing a spring in the base of a mobile vertical antenna to make it more flexible D. Strengthening the radiating elements of a beam antenna to better resist wind damage T9A03 (B) Which of the following describes a simple dipole oriented parallel to Earth's surface? A. A ground-wave antenna B. A horizontally polarized antenna C. A travelling-wave antenna D. A vertically polarized antenna T9A04 (A) What is a disadvantage of the short, flexible antenna supplied with most handheld radio transceivers, compared to a full-sized quarter-wave antenna? A. It has low efficiency B. It transmits only circularly polarized signals C. It is mechanically fragile D. All these choices are correct T9A05 (C) Which of the following increases the resonant frequency of a dipole antenna? A. Lengthening it B. Inserting coils in series with radiating wires C. Shortening it D. Adding capacitive loading to the ends of the radiating wires T9A06 (D) Which of the following types of antenna offers the greatest gain? A. 5/8 wave vertical B. Isotropic C. J pole D. Yagi T9A07 (A) What is a disadvantage of using a handheld VHF transceiver with a flexible antenna inside a vehicle? A. Signal strength is reduced due to the shielding effect of the vehicle B. The bandwidth of the antenna will decrease, increasing SWR C. The SWR might decrease, decreasing the signal strength D. All these choices are correct T9A08 (C) What is the approximate length, in inches, of a quarter-wavelength vertical antenna for 146 MHz? A. 112 B. 50 C. 19 D. 12 T9A09 (C) What is the approximate length, in inches, of a half-wavelength 6 meter dipole antenna? A. 6 B. 50 C. 112 D. 236 T9A10 (D) In which direction does a half-wave dipole antenna radiate the strongest signal? A. Equally in all directions B. Off the ends of the antenna C. In the direction of the feed line D. Broadside to the antenna T9A11 (C) What is antenna gain? A. The additional power that is added to the transmitter power B. The additional power that is required in the antenna when transmitting on a higher frequency C. The increase in signal strength in a specified direction compared to a reference antenna D. The increase in impedance on receive or transmit compared to a reference antenna T9A12 (A) What is an advantage of a 5/8 wavelength whip antenna for VHF or UHF mobile service? A. It has more gain than a 1/4-wavelength antenna B. It radiates at a very high angle C. It eliminates distortion caused by reflected signals D. It has 10 times the power gain of a 1/4 wavelength whip T9B01 (B) What is a benefit of low SWR? A. Reduced television interference B. Reduced signal loss C. Less antenna wear D. All these choices are correct T9B02 (B) What is the most common impedance of coaxial cables used in amateur radio? A. 8 ohms B. 50 ohms C. 600 ohms D. 12 ohms T9B03 (A) Why is coaxial cable the most common feed line for amateur radio antenna systems? A. It is easy to use and requires few special installation considerations B. It has less loss than any other type of feed line C. It can handle more power than any other type of feed line D. It is less expensive than any other type of feed line T9B04 (A) What is the major function of an antenna tuner (antenna coupler)? A. It matches the antenna system impedance to the transceiver's output impedance B. It helps a receiver automatically tune in weak stations C. It allows an antenna to be used on both transmit and receive D. It automatically selects the proper antenna for the frequency band being used T9B05 (D) What happens as the frequency of a signal in coaxial cable is increased? A. The characteristic impedance decreases B. The loss decreases C. The characteristic impedance increases D. The loss increases T9B06 (B) Which of the following RF connector types is most suitable for frequencies above 400 MHz? A. UHF (PL-259/SO-239) B. Type N C. RS-213 D. DB-25 T9B07 (C) Which of the following is true of PL-259 type coax connectors? A. They are preferred for microwave operation B. They are watertight C. They are commonly used at HF and VHF frequencies D. They are a bayonet-type connector T9B08 (D) Which of the following is a source of loss in coaxial feed line? A. Water intrusion into coaxial connectors B. High SWR C. Multiple connectors in the line D. All these choices are correct T9B09 (B) What can cause erratic changes in SWR? A. Local thunderstorm B. Loose connection in the antenna or feed line C. Over-modulation D. Overload from a strong local station T9B10 (C) What is the electrical difference between RG-58 and RG-213 coaxial cable? A. There is no significant difference between the two types B. RG-58 cable has two shields C. RG-213 cable has less loss at a given frequency D. RG-58 cable can handle higher power levels T9B11 (C) Which of the following types of feed line has the lowest loss at VHF and UHF? A. 50-ohm flexible coax B. Multi-conductor unbalanced cable C. Air-insulated hardline D. 75-ohm flexible coax T9B12 (A) What is standing wave ratio (SWR)? A. A measure of how well a load is matched to a transmission line B. The ratio of amplifier power output to input C. The transmitter efficiency ratio D. An indication of the quality of your station’s ground connection T0A01 (B) Which of the following is a safety hazard of a 12-volt storage battery? A. Touching both terminals with the hands can cause electrical shock B. Shorting the terminals can cause burns, fire, or an explosion C. RF emissions from a nearby transmitter can cause the electrolyte to emit poison gas D. All these choices are correct T0A02 (D) What health hazard is presented by electrical current flowing through the body? A. It may cause injury by heating tissue B. It may disrupt the electrical functions of cells C. It may cause involuntary muscle contractions D. All these choices are correct T0A03 (B) In the United States, what circuit does black wire insulation indicate in a three-wire 120 V cable? A. Neutral B. Hot C. Equipment ground D. Black insulation is never used T0A04 (B) What is the purpose of a fuse in an electrical circuit? A. To prevent power supply ripple from damaging a component B. To remove power in case of overload C. To limit current to prevent shocks D. All these choices are correct T0A05 (C) Why should a 5-ampere fuse never be replaced with a 20-ampere fuse? A. The larger fuse would be likely to blow because it is rated for higher current B. The power supply ripple would greatly increase C. Excessive current could cause a fire D. All these choices are correct T0A06 (D) What is a good way to guard against electrical shock at your station? A. Use three-wire cords and plugs for all AC powered equipment B. Connect all AC powered station equipment to a common safety ground C. Install mechanical interlocks in high-voltage circuits D. All these choices are correct T0A07 (D) Where should a lightning arrester be installed in a coaxial feed line? A. At the output connector of a transceiver B. At the antenna feed point C. At the ac power service panel D. On a grounded panel near where feed lines enter the building T0A08 (A) Where should a fuse or circuit breaker be installed in a 120V AC power circuit? A. In series with the hot conductor only B. In series with the hot and neutral conductors C. In parallel with the hot conductor only D. In parallel with the hot and neutral conductors T0A09 (C) What should be done to all external ground rods or earth connections? A. Waterproof them with silicone caulk or electrical tape B. Keep them as far apart as possible C. Bond them together with heavy wire or conductive strap D. Tune them for resonance on the lowest frequency of operation T0A10 (A) What hazard is caused by charging or discharging a battery too quickly? A. Overheating or out-gassing B. Excess output ripple C. Half-wave rectification D. Inverse memory effect T0A11 (D) What hazard exists in a power supply immediately after turning it off? A. Circulating currents in the dc filter B. Leakage flux in the power transformer C. Voltage transients from kickback diodes D. Charge stored in filter capacitors T0A12 (B) Which of the following precautions should be taken when measuring high voltages with a voltmeter? A. Ensure that the voltmeter has very low impedance B. Ensure that the voltmeter and leads are rated for use at the voltages to be measured C. Ensure that the circuit is grounded through the voltmeter D. Ensure that the voltmeter is set to the correct frequency T0B01 (C) Which of the following is good practice when installing ground wires on a tower for lightning protection? A. Put a drip loop in the ground connection to prevent water damage to the ground system B. Make sure all ground wire bends are right angles C. Ensure that connections are short and direct D. All these choices are correct T0B02 (D) What is required when climbing an antenna tower? A. Have sufficient training on safe tower climbing techniques B. Use appropriate tie-off to the tower at all times C. Always wear an approved climbing harness D. All these choices are correct T0B03 (D) Under what circumstances is it safe to climb a tower without a helper or observer? A. When no electrical work is being performed B. When no mechanical work is being performed C. When the work being done is not more than 20 feet above the ground D. Never T0B04 (C) Which of the following is an important safety precaution to observe when putting up an antenna tower? A. Wear a ground strap connected to your wrist at all times B. Insulate the base of the tower to avoid lightning strikes C. Look for and stay clear of any overhead electrical wires D. All these choices are correct T0B05 (B) What is the purpose of a safety wire through a turnbuckle used to tension guy lines? A. Secure the guy line if the turnbuckle breaks B. Prevent loosening of the turnbuckle from vibration C. Provide a ground path for lightning strikes D. Provide an ability to measure for proper tensioning T0B06 (D) What is the minimum safe distance from a power line to allow when installing an antenna? A. Add the height of the antenna to the height of the power line and multiply by a factor of 1.5 B. The height of the power line above ground C. 1/2 wavelength at the operating frequency D. Enough so that if the antenna falls, no part of it can come closer than 10 feet to the power wires T0B07 (C) Which of the following is an important safety rule to remember when using a crank-up tower? A. This type of tower must never be painted B. This type of tower must never be grounded C. This type of tower must not be climbed unless it is retracted, or mechanical safety locking devices have been installed D. All these choices are correct T0B08 (D) Which is a proper grounding method for a tower? A. A single four-foot ground rod, driven into the ground no more than 12 inches from the base B. A ferrite-core RF choke connected between the tower and ground C. A connection between the tower base and a cold water pipe D. Separate eight-foot ground rods for each tower leg, bonded to the tower and each other T0B09 (C) Why should you avoid attaching an antenna to a utility pole? A. The antenna will not work properly because of induced voltages B. The 60 Hz radiations from the feed line may increase the SWR C. The antenna could contact high-voltage power lines D. All these choices are correct T0B10 (C) Which of the following is true when installing grounding conductors used for lightning protection? A. Use only non-insulated wire B. Wires must be carefully routed with precise right-angle bends C. Sharp bends must be avoided D. Common grounds must be avoided T0B11 (B) Which of the following establishes grounding requirements for an amateur radio tower or antenna? A. FCC Part 97 rules B. Local electrical codes C. FAA tower lighting regulations D. UL recommended practices T0C01 (D) What type of radiation are radio signals? A. Gamma radiation B. Ionizing radiation C. Alpha radiation D. Non-ionizing radiation T0C02 (B) At which of the following frequencies does maximum permissible exposure have the lowest value? A. 3.5 MHz B. 50 MHz C. 440 MHz D. 1296 MHz T0C03 (C) How does the allowable power density for RF safety change if duty cycle changes from 100 percent to 50 percent? A. It increases by a factor of 3 B. It decreases by 50 percent C. It increases by a factor of 2 D. There is no adjustment allowed for lower duty cycle T0C04 (D) What factors affect the RF exposure of people near an amateur station antenna? A. Frequency and power level of the RF field B. Distance from the antenna to a person C. Radiation pattern of the antenna D. All these choices are correct T0C05 (D) Why do exposure limits vary with frequency? A. Lower frequency RF fields have more energy than higher frequency fields B. Lower frequency RF fields do not penetrate the human body C. Higher frequency RF fields are transient in nature D. The human body absorbs more RF energy at some frequencies than at others T0C06 (D) Which of the following is an acceptable method to determine whether your station complies with FCC RF exposure regulations? A. By calculation based on FCC OET Bulletin 65 B. By calculation based on computer modeling C. By measurement of field strength using calibrated equipment D. All these choices are correct T0C07 (B) What hazard is created by touching an antenna during a transmission? A. Electrocution B. RF burn to skin C. Radiation poisoning D. All these choices are correct T0C08 (A) Which of the following actions can reduce exposure to RF radiation? A. Relocate antennas B. Relocate the transmitter C. Increase the duty cycle D. All these choices are correct T0C09 (B) How can you make sure your station stays in compliance with RF safety regulations? A. By informing the FCC of any changes made in your station B. By re-evaluating the station whenever an item in the transmitter or antenna system is changed C. By making sure your antennas have low SWR D. All these choices are correct T0C10 (A) Why is duty cycle one of the factors used to determine safe RF radiation exposure levels? A. It affects the average exposure to radiation B. It affects the peak exposure to radiation C. It takes into account the antenna feed line loss D. It takes into account the thermal effects of the final amplifier T0C11 (C) What is the definition of duty cycle during the averaging time for RF exposure? A. The difference between the lowest power output and the highest power output of a transmitter B. The difference between the PEP and average power output of a transmitter C. The percentage of time that a transmitter is transmitting D. The percentage of time that a transmitter is not transmitting T0C12 (A) How does RF radiation differ from ionizing radiation (radioactivity)? A. RF radiation does not have sufficient energy to cause chemical changes in cells and damage DNA B. RF radiation can only be detected with an RF dosimeter C. RF radiation is limited in range to a few feet D. RF radiation is perfectly safe T0C13 (B) Who is responsible for ensuring that no person is exposed to RF energy above the FCC exposure limits? A. The FCC B. The station licensee C. Anyone who is near an antenna D. The local zoning board